-
-
Notifications
You must be signed in to change notification settings - Fork 266
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
Mark that the power_dist documentation has moved.
- Loading branch information
Showing
1 changed file
with
2 additions
and
101 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -1,102 +1,3 @@ | ||
| mjbots power dist reference | ||
| This document has moved to: | ||
|
|
||
| # A. Operation # | ||
|
|
||
| This documentation refers to the most recent (r3.1) version of the | ||
| board. | ||
|
|
||
| The power dist board provides pre-charging, a soft power switch, and a | ||
| power connector fanout for use in robotic applications. The input can | ||
| be directly connected to a battery or power supply. The output can be | ||
| connected to high capacitance loads. When the switch is enabled, the | ||
| board will first apply power through a limiting resistor to "charge | ||
| up" the output capacitance for 100ms before connecting the low | ||
| impedance source. | ||
|
|
||
| Additionally, a 125 kbps CAN port allows robot software to monitor the | ||
| state of the switch and request a "soft power down". | ||
|
|
||
| ## Specifications ## | ||
|
|
||
| * Input voltage: 8-34V | ||
| * Peak current: 90A | ||
| * Continuous current: 45A | ||
| * Quiescent current (off): 3mA | ||
| * Dimensions: 45x70mm | ||
| * Mass: 28.3g | ||
| * Connectors: | ||
| * Input: Optional Amass XT90 | ||
| * Output: 6x Amass XT30 | ||
| * CAN: 2x JST-PH3 | ||
| * Switch and LED: JST-PH4 | ||
| * STM32 SWD: JST-ZH6 | ||
|
|
||
| ## Mounting ## | ||
|
|
||
| 4x M2.5 mounting holes are provided in a 64mm x 39mm rectangular | ||
| pattern. | ||
|
|
||
| # B. CAN protocol # | ||
|
|
||
| The power dist board emits the following CAN frame at 10Hz. | ||
|
|
||
| * CAN ID: 0x10004 | ||
| * byte 0: Switch status (0 is off, 1 is on) | ||
| * byte 1: Lock time in 0.1s intervals | ||
|
|
||
| It listens for a frame of the following properties: | ||
|
|
||
| * CAN ID: 0x10005 | ||
| * byte 0: Reserved, keep at 0 | ||
| * byte 1: Lock time in 0.1s intervals | ||
|
|
||
| While the lock time is non-zero, the power switch will not turn off | ||
| the output load until the count does reach zero. An application which | ||
| desires soft power down can periodically "kick" the lock interval to | ||
| keep power applied, then stop doing so when it is ready for the power | ||
| to turn off. | ||
|
|
||
| # C. pinout # | ||
|
|
||
| ## XT-90 Input ## | ||
|
|
||
| The XT-90 connector has a `-` and a `+` imprint on the housing. | ||
|
|
||
| ## XT-30 Output ## | ||
|
|
||
| The XT-30 connectors have a `-` and a `+` imprint on the housing. | ||
|
|
||
| ## JST PH-4 Switch ## | ||
|
|
||
| Looking at the pins of the connector from the top with the mjbots logo | ||
| right side up the pins are numbered from right to left. | ||
|
|
||
| - 1 - LED+ - LED positive | ||
| - 2 - LED- - LED ground | ||
| - 3 - SWP - Switch positive | ||
| - 4 - SWG - Switch ground | ||
|
|
||
| ## JST PH-3 CAN ## | ||
|
|
||
| Looking at the pins of the connector with the mjbots logo right side | ||
| up, the pins are numbered from the bottom to the top. | ||
|
|
||
| - 1 - CAN_H | ||
| - 2 - CAN_L | ||
| - 3 - GND | ||
|
|
||
| NOTE: This ground IS NOT the same as the output ground. DO NOT | ||
| connect ground from the CAN connector to an output load. `CAN_H` and | ||
| `CAN_L` are fine to connect, just not ground. | ||
|
|
||
| ## JST ZH-6 SWD ## | ||
|
|
||
| Looking at the pins of the connector with the mjbots logo right side | ||
| up the pins are numbered 1 to 6 from top to bottom. | ||
|
|
||
| - 1 - NC | ||
| - 2 - NRST | ||
| - 3 - SWDIO | ||
| - 4 - GND | ||
| - 5 - SWCLK | ||
| - 6 - 3.3V | ||
| https://github.com/mjbots/power_dist/ |