Skip to content

This project is a Java application for a leJOS mindstorm robot to draw shapes like a diamond inside a rectangle or an anchor. This program can be extended to plot other shapes.

License

Notifications You must be signed in to change notification settings

brianpinto91/leJOS-NXT-2D-plotter

Repository files navigation

A 2D shape plotter leJOS NXT robot

GitHub repo size CodeFactor Grade

This project is a Java application for a leJOS mindstorm robot to draw shapes like a diamond inside a rectangle or an anchor. This program can be extended to plot other shapes.

Table of Contents

Robot

The robot is built using Lego Mindstorms NXT Robotic kit. At the heart of the robot is the NXT brick on which the JAVA application runs using LeJOS firmware version 0.9.1 beta.

The assembled robot along with the plotting board is shown in the below figure.

leJOS Robot

The robot has three motors: one motor drives the robot forward and backward. Another one moves the swivel arm, on which the pen is mounted, left and right. The third motor moves the pen up and down (by coiling a rope on a reel). Three sensors are installed for calibration purposes: a touch sensor allows determining when the motor driving the swivel arm is in its rightmost position. Another touch sensor detects if the pen reaches its maximum upper position. A light sensor enables the robot to find a black bar, which marks the start of the drawing area.

The motors and sensors are connected to the NXT brick as follows:

Port Usage
SensorPort.S1 Touch sensor of Swivel arm
SensorPort.S2 Touch sensor of pen
SensorPort.S3 Light Sensor
Motor.A Swivel arm rotation
Motor.B Pen up/down
Motor.C Wheels drive

Plotting-surface Coordinate System

The software uses a Cartesian coordinate system to define locations in two dimensions x and y. As shown in below figure, the y-direction is defined as the direction in which the robot moves forward and backward. The position y = 0 is located at the upper edge of the black bar (shown in gray). The x-direction is orthogonal to y and has its x = 0 value in the middle of the robot which is the horizontal midway on the plotting surface in ideal case when the robot is exactly placed in the middle before starting. Otjerwise the middle of the robot along the horizontal direction at which the robot is placed is considered to be x=0. The radius of the swivel arm holding the pen is represented by 'r' in the figure. The robot cannot move in the x-direction. So the limits of the points that can be reached along the x-axis is determined by the length of the swivel arm and its maximum rotation angle determined through calibration before plotting.

Since the robot cannot move in the horizontal direction, plotting at points other than along the y-axis is challenging. Co-ordinated wheel and swivel arm movement is used for this purpose using mathematical calculations and is implemented in the software.

Installation

The instructions here are for installation using a Linux host machine. For Windows host machine refer the documentation here.

On your computer, first navigate to the directory were you want to download the repository to. Then run the following commands:

git clone --depth 1 https://github.com/brianpinto91/leJOS-NXT-2D-plotter.git

There are two options to install the software on the NXT brick

Using the leJOS NXJ command line tools on Linux

The Java code uses the leJOS_NXJ library to interface with the sensors, the motors, and also the buttons on the NXT brick. This requires the compilation and linking to be done using the leJOS SDK. Follow this guide to download and install it.

Create a new directory build inside the parent leJOS-NXT-2D-plotter directory. Then use the below command to compile the source java files into this new directory. (Make sure to navigate to the parent directory on the command line before executing this command)

nxjc -d build src/plotbot/*.java

If this step is successful, you will find the compiled .class files for all the .java files in the build directory.

The next step is to link the leJOS class library and create an executable. The main class file is the Plotbot.class. Use the below commands sequentially to create an executable:

cd build
nxjlink -v -o plotter.nxj plotbot/Plotbot

You will find plotter.nxj executable file created in the build directory. This file is now ready to be uploaded to the NXT brick.

Make sure that your NXT brick is connected to the host PC using either USB or bluetooth. Then run the following command:

nxjupload plotter.nxj

Now you are ready to use the NXT brick on the robot to plot different shapes!

Installation using Eclipse IDE

For this you need to install Eclipse IDE and the leJOS Eclipse plugin as described in this guide.

Open the cloned github repository in Eclipse. In the project explorer on the left side right click on the parent directory. In the list you will find an option leJOS NXJ. Expand this option and click on Convert to leJOS NXJ project.

Then, in the top navigation bar choose Window --> ShowView --> Ant. A new window titled Ant appears (on right hand side, near Outline in case you use the default layout). Drag and drop the file build.xml from the project explorer into the Ant window. You will now see various options in the Ant window.

Connect the NXT brick using bluettoth or usb and then select Upload option in the Ant window and click on the play button. That's it, your robot is ready to plot.

Technologies

forthebadge-java



License

License: MIT

Copyright 2020 Brian Pinto

About

This project is a Java application for a leJOS mindstorm robot to draw shapes like a diamond inside a rectangle or an anchor. This program can be extended to plot other shapes.

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages