Skip to content

Commit

Permalink
Examples Customizations
Browse files Browse the repository at this point in the history
  • Loading branch information
@thinkyhead
thinkyhead committed Sep 13, 2022
1 parent 4cbd105 commit ca39876
Show file tree
Hide file tree
Showing 597 changed files with 31,679 additions and 27,535 deletions.
169 changes: 98 additions & 71 deletions config/examples/3DFabXYZ/Migbot/Configuration.h
View file

Large diffs are not rendered by default.

75 changes: 37 additions & 38 deletions config/examples/3DFabXYZ/Migbot/Configuration_adv.h
View file
Original file line number Diff line number Diff line change
Expand Up @@ -21,6 +21,8 @@
*/
#pragma once

#define CONFIG_EXAMPLES_DIR "3DFabXYZ/Migbot"

/**
* Configuration_adv.h
*
Expand Down Expand Up @@ -529,13 +531,13 @@
* The fan turns on automatically whenever any driver is enabled and turns
* off (or reduces to idle speed) shortly after drivers are turned off.
*/
//#define USE_CONTROLLER_FAN
#define USE_CONTROLLER_FAN
#if ENABLED(USE_CONTROLLER_FAN)
//#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
#define CONTROLLER_FAN_PIN 7 // Set a custom pin for the controller fan
//#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered
//#define CONTROLLER_FAN_IGNORE_Z // Ignore Z stepper. Useful when stepper timeout is disabled.
#define CONTROLLERFAN_SPEED_MIN 0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
#define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
#define CONTROLLERFAN_SPEED_ACTIVE 127 // (0-255) Active speed, used when any motor is enabled
#define CONTROLLERFAN_SPEED_IDLE 0 // (0-255) Idle speed, used when motors are disabled
#define CONTROLLERFAN_IDLE_TIME 60 // (seconds) Extra time to keep the fan running after disabling motors

Expand Down Expand Up @@ -694,15 +696,15 @@
/**
* M355 Case Light on-off / brightness
*/
//#define CASE_LIGHT_ENABLE
#define CASE_LIGHT_ENABLE
#if ENABLED(CASE_LIGHT_ENABLE)
//#define CASE_LIGHT_PIN 4 // Override the default pin if needed
#define CASE_LIGHT_PIN 11 // Override the default pin if needed
#define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
#define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
#define CASE_LIGHT_DEFAULT_ON false // Set default power-up state on
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
//#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
//#define CASE_LIGHT_MAX_PWM 128 // Limit PWM duty cycle (0-255)
//#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
#if ENABLED(NEOPIXEL_LED)
//#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light
#endif
Expand Down Expand Up @@ -1004,7 +1006,7 @@

// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
#define G34_MAX_GRADE 5 // (%) Maximum incline that G34 will handle
#define Z_STEPPER_ALIGN_ITERATIONS 5 // Number of iterations to apply during alignment
#define Z_STEPPER_ALIGN_ITERATIONS 3 // Number of iterations to apply during alignment
#define Z_STEPPER_ALIGN_ACC 0.02 // Stop iterating early if the accuracy is better than this
#define RESTORE_LEVELING_AFTER_G34 // Restore leveling after G34 is done?
// After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
Expand Down Expand Up @@ -1081,8 +1083,8 @@
#define DISABLE_INACTIVE_E true

// Default Minimum Feedrates for printing and travel moves
#define DEFAULT_MINIMUMFEEDRATE 0.0 // (mm/s. °/s for rotational-only moves) Minimum feedrate. Set with M205 S.
#define DEFAULT_MINTRAVELFEEDRATE 0.0 // (mm/s. °/s for rotational-only moves) Minimum travel feedrate. Set with M205 T.
#define DEFAULT_MINIMUMFEEDRATE 0.0 // (mm/s) Minimum feedrate. Set with M205 S.
#define DEFAULT_MINTRAVELFEEDRATE 0.0 // (mm/s) Minimum travel feedrate. Set with M205 T.

// Minimum time that a segment needs to take as the buffer gets emptied
#define DEFAULT_MINSEGMENTTIME 20000 // (µs) Set with M205 B.
Expand Down Expand Up @@ -1221,7 +1223,7 @@
* vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
* lowest stepping frequencies.
*/
//#define ADAPTIVE_STEP_SMOOTHING
#define ADAPTIVE_STEP_SMOOTHING

/**
* Custom Microstepping
Expand Down Expand Up @@ -1307,8 +1309,8 @@
// Change values more rapidly when the encoder is rotated faster
#define ENCODER_RATE_MULTIPLIER
#if ENABLED(ENCODER_RATE_MULTIPLIER)
#define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed
#define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
#define ENCODER_10X_STEPS_PER_SEC 75 // (steps/s) Encoder rate for 10x speed
#define ENCODER_100X_STEPS_PER_SEC 160 // (steps/s) Encoder rate for 100x speed
#endif

// Play a beep when the feedrate is changed from the Status Screen
Expand Down Expand Up @@ -1360,7 +1362,7 @@
#endif

// Include a page of printer information in the LCD Main Menu
//#define LCD_INFO_MENU
#define LCD_INFO_MENU
#if ENABLED(LCD_INFO_MENU)
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
#endif
Expand Down Expand Up @@ -1390,7 +1392,7 @@
#endif

// Scroll a longer status message into view
//#define STATUS_MESSAGE_SCROLLING
#define STATUS_MESSAGE_SCROLLING
// Apply a timeout to low-priority status messages
//#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
Expand Down Expand Up @@ -1497,7 +1499,7 @@

//#define MEDIA_MENU_AT_TOP // Force the media menu to be listed on the top of the main menu

#define EVENT_GCODE_SD_ABORT "G28XY" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
#define EVENT_GCODE_SD_ABORT "G27" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")

#if ENABLED(PRINTER_EVENT_LEDS)
#define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
Expand Down Expand Up @@ -1579,7 +1581,7 @@
//#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
//#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol

//#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
//#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!)
Expand Down Expand Up @@ -2579,7 +2581,7 @@
*
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
*/
//#define ADVANCED_PAUSE_FEATURE
#define ADVANCED_PAUSE_FEATURE
#if ENABLED(ADVANCED_PAUSE_FEATURE)
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
Expand Down Expand Up @@ -2622,7 +2624,7 @@
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change

//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
#endif

Expand Down Expand Up @@ -3342,7 +3344,7 @@
* Add the M240 G-code to take a photo.
* The photo can be triggered by a digital pin or a physical movement.
*/
//#define PHOTO_GCODE
#define PHOTO_GCODE
#if ENABLED(PHOTO_GCODE)
// A position to move to (and raise Z) before taking the photo
//#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z)
Expand All @@ -3351,17 +3353,17 @@

// Canon RC-1 or homebrew digital camera trigger
// Data from: https://www.doc-diy.net/photo/rc-1_hacked/
//#define PHOTOGRAPH_PIN 23
//#define PHOTOGRAPH_PIN 12

// Canon Hack Development Kit
// https://captain-slow.dk/2014/03/09/3d-printing-timelapses/
//#define CHDK_PIN 4
#define CHDK_PIN 12

// Optional second move with delay to trigger the camera shutter
//#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J)

// Duration to hold the switch or keep CHDK_PIN high
//#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)
#define PHOTO_SWITCH_MS 50 // (ms) (M240 D)

/**
* PHOTO_PULSES_US may need adjustment depending on board and camera model.
Expand Down Expand Up @@ -3530,6 +3532,7 @@
*/
//#define LASER_POWER_TRAP


//
// Laser I2C Ammeter (High precision INA226 low/high side module)
//
Expand Down Expand Up @@ -3813,33 +3816,29 @@
// @section custom main menu

// Custom Menu: Main Menu
//#define CUSTOM_MENU_MAIN
#define CUSTOM_MENU_MAIN
#if ENABLED(CUSTOM_MENU_MAIN)
//#define CUSTOM_MENU_MAIN_TITLE "Custom Commands"
#define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
#define CUSTOM_MENU_MAIN_TITLE "Tools"
#define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 Done"
#define CUSTOM_MENU_MAIN_SCRIPT_AUDIBLE_FEEDBACK
//#define CUSTOM_MENU_MAIN_SCRIPT_RETURN // Return to status screen after a script
#define CUSTOM_MENU_MAIN_ONLY_IDLE // Only show custom menu when the machine is idle

#define MAIN_MENU_ITEM_1_DESC "Home & UBL Info"
#define MAIN_MENU_ITEM_1_GCODE "G28\nG29 W"
#define MAIN_MENU_ITEM_1_DESC "Probe Mesh&Save"
#define MAIN_MENU_ITEM_1_GCODE "G28\nG29 P1\nG29 P3 T0\nG29 S0 A F10\nG29 J2\nM500"
//#define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action

#define MAIN_MENU_ITEM_2_DESC "Preheat for " PREHEAT_1_LABEL
#define MAIN_MENU_ITEM_2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
#define MAIN_MENU_ITEM_2_DESC "Manual Mesh&Save"
#define MAIN_MENU_ITEM_2_GCODE "G28\nG29 P4 R999 T\nG29 S0 A F10\nM500"
//#define MAIN_MENU_ITEM_2_CONFIRM

//#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
//#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
#define MAIN_MENU_ITEM_3_DESC "Print Test Pattern"
#define MAIN_MENU_ITEM_3_GCODE "G26 C P O2.25" // Do a typical test sequence
//#define MAIN_MENU_ITEM_3_CONFIRM

//#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
//#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
#define MAIN_MENU_ITEM_4_DESC "Move Bed Forward"
#define MAIN_MENU_ITEM_4_GCODE "G28 X0 Y0\nG1 X0 Y180 F3000\nM84" // move X/Y to min endstops & Feed the bed forward & steppers off
//#define MAIN_MENU_ITEM_4_CONFIRM

//#define MAIN_MENU_ITEM_5_DESC "Home & Info"
//#define MAIN_MENU_ITEM_5_GCODE "G28\nM503"
//#define MAIN_MENU_ITEM_5_CONFIRM
#endif

// @section custom config menu
Expand Down
Loading

0 comments on commit ca39876

Please sign in to comment.