🔧 Tuning for Sovol SV06 (#1088)

config/examples/Sovol/SV-06/Configuration.h

@@ -1266,7 +1266,7 @@
  * Override with M203
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 500, 500, 10, 30 }
+#define DEFAULT_MAX_FEEDRATE          { 300, 300, 10, 100 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -1314,10 +1314,10 @@
  */
 #define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
-  #define DEFAULT_XJERK  8.0
-  #define DEFAULT_YJERK  8.0
+  #define DEFAULT_XJERK  5.0
+  #define DEFAULT_YJERK  5.0
   #define DEFAULT_ZJERK  0.4
-  #define DEFAULT_EJERK  5.0
+  #define DEFAULT_EJERK 10.0
   //#define DEFAULT_IJERK  0.3
   //#define DEFAULT_JJERK  0.3
   //#define DEFAULT_KJERK  0.3
@@ -1606,7 +1606,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 25, -25, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { 28, -20, 0 }
 
 // Enable and set to use a specific tool for probing. Disable to allow any tool.
 #define PROBING_TOOL 0
@@ -1616,7 +1616,7 @@
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-//#define PROBING_MARGIN 10
+#define PROBING_MARGIN 0
 
 // X and Y axis travel speed (mm/min) between probes
 #define XY_PROBE_FEEDRATE (60*60)
@@ -1928,12 +1928,12 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
-  #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
+  #define FIL_RUNOUT_ENABLED_DEFAULT false // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
 
-  #define FIL_RUNOUT_STATE     HIGH       // Pin state indicating that filament is NOT present.
+  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
   #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
   //#define WATCH_ALL_RUNOUT_SENSORS      // Execute runout script on any triggering sensor, not only for the active extruder.
@@ -2170,7 +2170,7 @@
     // Subdivision of the grid by Catmull-Rom method.
     // Synthesizes intermediate points to produce a more detailed mesh.
     //
-    //#define ABL_BILINEAR_SUBDIVISION
+    #define ABL_BILINEAR_SUBDIVISION
     #if ENABLED(ABL_BILINEAR_SUBDIVISION)
       // Number of subdivisions between probe points
       #define BILINEAR_SUBDIVISIONS 3

config/examples/Sovol/SV-06/Configuration_adv.h

@@ -1195,8 +1195,8 @@
  *
  * Tune with M593 D<factor> F<frequency>
  */
-//#define INPUT_SHAPING_X
-//#define INPUT_SHAPING_Y
+#define INPUT_SHAPING_X
+#define INPUT_SHAPING_Y
 //#define INPUT_SHAPING_Z
 #if ANY(INPUT_SHAPING_X, INPUT_SHAPING_Y, INPUT_SHAPING_Z)
   #if ENABLED(INPUT_SHAPING_X)
@@ -1213,7 +1213,7 @@
   #endif
   //#define SHAPING_MIN_FREQ  20.0      // (Hz) By default the minimum of the shaping frequencies. Override to affect SRAM usage.
   //#define SHAPING_MAX_STEPRATE 10000  // By default the maximum total step rate of the shaped axes. Override to affect SRAM usage.
-  //#define SHAPING_MENU                // Add a menu to the LCD to set shaping parameters.
+  #define SHAPING_MENU                  // Add a menu to the LCD to set shaping parameters.
 #endif
 
 // @section motion
@@ -2005,10 +2005,10 @@
    */
   //#define STATUS_COMBINE_HEATERS    // Use combined heater images instead of separate ones
   //#define STATUS_HOTEND_NUMBERLESS  // Use plain hotend icons instead of numbered ones (with 2+ hotends)
-  #define STATUS_HOTEND_INVERTED      // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM for numbered hotends)
-  #define STATUS_HOTEND_ANIM          // Use a second bitmap to indicate hotend heating
-  #define STATUS_BED_ANIM             // Use a second bitmap to indicate bed heating
-  #define STATUS_CHAMBER_ANIM         // Use a second bitmap to indicate chamber heating
+  //#define STATUS_HOTEND_INVERTED    // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM for numbered hotends)
+  //#define STATUS_HOTEND_ANIM        // Use a second bitmap to indicate hotend heating
+  //#define STATUS_BED_ANIM           // Use a second bitmap to indicate bed heating
+  //#define STATUS_CHAMBER_ANIM       // Use a second bitmap to indicate chamber heating
   //#define STATUS_CUTTER_ANIM        // Use a second bitmap to indicate spindle / laser active
   //#define STATUS_COOLER_ANIM        // Use a second bitmap to indicate laser cooling
   //#define STATUS_FLOWMETER_ANIM     // Use multiple bitmaps to indicate coolant flow
@@ -3025,7 +3025,7 @@
     #define Z_MICROSTEPS     16
     #define Z_RSENSE          0.15
     #define Z_CHAIN_POS      -1
-    #define Z_INTERPOLATE false
+    //#define Z_INTERPOLATE true
     //#define Z_HOLD_MULTIPLIER 0.5
   #endif
 
@@ -4289,8 +4289,8 @@
   #define GANTRY_CALIBRATION_FEEDRATE         240     // Feedrate for correction move
   //#define GANTRY_CALIBRATION_TO_MIN                 // Enable to calibrate Z in the MIN direction
 
-  //#define GANTRY_CALIBRATION_SAFE_POSITION XY_CENTER // Safe position for nozzle
-  //#define GANTRY_CALIBRATION_XY_PARK_FEEDRATE 3000  // XY Park Feedrate - MMM
+  #define GANTRY_CALIBRATION_SAFE_POSITION { X_CENTER + 3, Y_CENTER } // Safe position for nozzle
+  #define GANTRY_CALIBRATION_XY_PARK_FEEDRATE 3000    // XY Park Feedrate - MMM
   //#define GANTRY_CALIBRATION_COMMANDS_PRE   ""
   #define GANTRY_CALIBRATION_COMMANDS_POST  "G28 Z"   // G28 highly recommended to ensure an accurate position
 #endif